Both names start with “poly”, both come in drums, and both end up as a rubbery waterproof skin. So why do engineers argue about polyurea vs polyurethane? The answer lies in chemistry, cure speed and application method. This guide compares the two using only Krypton’s technical datasheets: Polyurea Rayston for pure polyurea, Impermax for one-component polyurethane and Impermax Polyurea H for the hybrid in between.

Polyurea vs polyurethane: the chemistry in one paragraph
Both membranes start from an isocyanate. The difference, however, is the partner it reacts with. According to Krypton Chemical’s note on key factors for applying polyurethanes and polyureas, amines (polyureas) cure ultra-fast, in seconds, with two-component machines at high pressure and temperature. Polyols (polyurethanes) cure slowly or moderately, by roller, gun or hand mixing. Meanwhile, one-component products react with moisture in the air, so humidity and temperature set the pace.
The datasheets confirm this. The Polyurea Rayston TDS lists component A as a polyamine and component B as an aromatic isocyanate prepolymer. In contrast, the Impermax TDS describes a solvent-borne, single-component aromatic polyurethane.
Polyurea vs polyurethane in numbers
To begin with, here are the headline values from each TDS. Always read them as datasheet values, not site guarantees.
Polyurea Rayston (pure polyurea, hot spray)
- Gel time: 4 s at 25 °C.
- Hardness: 87A/35D.
- Elongation and tensile: 324% and 16.2 MPa.
- Consumption: 1.5–2.0 kg/m² for 1.5–2 mm.
- Certificates: CE to EN 1504-2 (0370-CPR-2247), ETA 16/0148, BBA 18/5582 and WRAS approval.
Impermax (one-component polyurethane, cold applied)
- Pot life: 4–6 hours (1 kg, 20 °C, 50% RH).
- Hardness: 65–70 A.
- Elongation and tensile: 450–600% and 2.5–4.3 MPa.
- Application: roller, brush, spreader or airless, ideally in two coats of 1 kg/m² each.
- Certificates: ETA 06/0263, BBA 11/4836, BROOF(t1) for any roof slope and BROOF(t4).
The pattern is clear. The polyurethane stretches further, while the polyurea is harder and much stronger in tension. Likewise, the polyurea cures in seconds, whereas the polyurethane stays workable for hours.
Polyurea vs polyurethane: cure speed and return to service
Speed is where the two differ most on site. The Impermax TDS says the membrane reaches up to 90% of its final properties in 3 days under usual conditions. Walking time is usually 1 or 2 days, and final hardness takes 10 or 15 days.
By contrast, the Polyurea Rayston TDS says it cures to touch a few minutes after application. Its reference table shows about 70 Shore A after 1 hour on a 1 mm film. As a result, a polyurea roof or tank can return to service far sooner.

Polyurea vs polyurethane on site: substrate and climate
Both membranes need a sound support. However, the limits differ slightly. The Polyurea Rayston TDS asks for a pull-off strength of at least 1.4 N/mm², a support temperature between 10 °C and 40 °C and support moisture below 4%. If underlying moisture is suspected, it recommends two coats of epoxy primer.
The Impermax TDS, on the other hand, asks for a minimum pull-off of 1.5 N/mm². Because it cures with air moisture, its curing rate increases as temperature and humidity rise. For example, its table gives a dry-to-touch time of 8–9 hours at 24 °C and 52% RH. At 43 °C and 50% RH, it drops to 3–4 hours. Yet in dry desert air, at 43 °C and 12% RH, it rises to 12–14 hours. Furthermore, the TDS lists thermal stability up to 140 °C, and it resists the heat impact of poured hot asphalt at 160 °C.
In practice, this means polyurea depends on the machine and the crew, while polyurethane depends on the weather. Plan accordingly.
The hybrid: between polyurea and polyurethane
Besides these two, Krypton also makes a third family. The Impermax Polyurea H TDS lists component A as polyol/polyamine and component B as an aromatic isocyanate prepolymer. In other words, it is a hybrid.
Even so, it still sprays hot, with a gel time of 8–9 s at 25 °C. Under usual conditions (25 °C, 50% RH), its TDS says it resists rain droplets after 15 minutes and light foot traffic after 1 hour. After 2 days, it reaches 90% of its final properties. For a deeper roof comparison, see Krypton’s note on pure polyurea vs hybrid on roofs.
Which one should you choose?
Krypton’s advice is to start from geometry, then choose the chemistry. Its note on why rheology decides the membrane puts it simply: hot-spray polyurea suits large, irregular or vertical surfaces. Cold one-component PU, on the other hand, is rolled or sprayed and cures with air moisture.
- Choose pure polyurea for large areas, tanks, vertical walls and fast return to service. Read more on Polyurea Rayston.
- Choose one-component polyurethane for small roofs, balconies, details and jobs without a spray rig.
- Choose a hybrid when you want hot-spray speed on roofs and terraces.
Quote the certificate for the right product
A common error is to borrow certificates across chemistries. Krypton’s guide to reading an ETA for a liquid-applied membrane is blunt: ETA 06/0263 belongs to the Impermax 1K family, and WRAS to Polyurea Rayston. Similarly, a BBA number belongs to one product only. You can verify certificates on the BBA website.
Frequently asked questions
Is polyurea always better than polyurethane?
No. Admittedly, polyurea is faster and stronger, but polyurethane stretches further and needs no spray machine. The right choice depends on the job.
Do both change colour in the sun?
Both TDS describe aromatic products and expect a colour change in sunlight. However, both state that this change does not affect the properties.
For our earlier product guides, see Polyurea Rayston and Impermax LY liquid polyurethane.


No comment